Chat - Gaba Hobby Atendimento Online - Gaba Hobby CDE Atendimento Online - Gaba Hobby PJC
Fabricante: FUTABA

Futaba 6EX 6-Channel 2.4GHz Air/Heli w/4 S3001 Servos FUTK6902

47357


Disponibilidade: Em Estoque

Aviso: Últimas unidades!


U$ 299.00

10x de U$ 29.90
Valor oficial: U$ 299.00


CEP:

 
Calcular
 
 
 


*Os valores não incluem I.V.A. – Imposto ao Valor Agregado (obrigatório para residentes no Paraguai) e podem sofrer alterações sem prévio aviso

This is the Futaba 6EX Heli Transmitter with the 2.4GHz FASST system,
          R617FS 6-ch Receiver and four S3001 Ball Bearing Servos.


FEATURES: Futaba's FASST (Futaba Advanced Spread Spectrum Technology) shifts
            very quickly virtually eliminating signal conficts and
            interruptions unlike other 2.4GHz systems that only stay on one
            or two frequencies
          R617FS high sensitivity receiver weighs only 0.25oz (7g) without case
            yet is a full range system for all aircraft from giant scale to
            Park Flyer applications-no need to buy separate receiver for
            specific aircraft
            rubber grommets installed where antennas exit to eliminate stress
            and fraying of the wires
          Dual antenna diversity enables FASST system to automatically and
            seamlessly select the best reception between the two antennas
            built into the receiver ensuring that the aircraft stays under
            constant control of transmitter regardless of altitude
          Pre-Vision Packet Screening technology scans incoming data for
            potential problems and applies sophisticated error correction
            techniques for solid impenetrable link with model
          Easy Link system features a unique ID code in the transmitter that
            links to the receiver insuring that receiver only follows commands
            from this transmitter-with over 134 million possible codes there
            is no chance for a conflict
          No hassle Fail Safe programmed through transmitter-no complicated
            set-up steps or binding plugs
          When performing a ground check, the Power Down function allows
            modeler to reduce power from up to 50+ paces away-like retracting
            the antenna on a conventional transmitter
          Purpose built custom IC chips for key functions; no off-the-shelf IC
            chips
          One year limited warranty


          Standard Programming Features:
            Trainer function-transmitter can be master or student, compatible
              with other Futaba systems
            Six model memory
            Servo reversing
            End point adjustment
            Airplane or heli programming
            Dual Rate /Exponential for ailerons, rudder and elevator
            Fail Safe-safety throttle setting in case of transmitter signal
              loss
            Battery Fail Safe-safety throttle setting in case of signal loss
            Stick Mode-Choose from Mode 1-Mode-4
            Changeable Throttle Stick-ratchet for airplanes or smooth for helis
            Adjustable Stick Length


          Airplane Features;
            Programmable Mixing (1 & 2) any two channels can be combined
            Pre-Programmed Throttle Cut for safely shutting off engine
            Wing mixing for flaperon, flap trim, V-tail and elevon


          Helicopter Functions;
            Three swashplate types
            Five-Point Normal and Idle Up Throttle/Pitch Curves
            Revo, Gyro and Swash to Throttle mixing
            Swash AFR Adjustable Function Rate for use w/ 3S or 3E swash type


INCLUDES: Futaba 6EX Transmitter
          NT8F600B 9.6V 600mAh NiCd Transmitter Battery, FUTM1440
          FBC-19B(4) 120V AC Battery Charger, FUTM1830
          Four S3001 Ball Bearing Servos, FUTM0029
          R617FS Receiver, FUTL7627
          Switch Harness-J Style Connector SWH13 FUTM4370
          Neck Strap, FUTM5690
          Servo mounting hardware and extra horn


REQUIRES: 4.8V receiver battery of modeler's choice


SPECS:    Transmitter;
            Power Supply: 9.6V
            Current Drain: 170mA


          Receiver;
            Size: 1.6 x 1.1 x 0.35" (40 x 27 x 9mm)
            Power Requirement: 4.8 - 6V
            Current Drain: 80mA (at no signal)
            Weight: 0.35oz (10g) with case
                    0.25oz  (7g) without case


          Servo;
            Length: 1.6" (41mm)° @ 4.8V
            Width:   .8" (20mm)
            Height: 1.4" (35mm) at 4.8V
            Weight: 1.6oz (45.1g)t 6.0V
            Torque: 33.3 oz-in at 4.8V  41.6 oz-in. at 6V
            Transit: .23 sec/60° @ 4.8V   .19 sec/60° @ 6V
            Connector: "J" type with approx. 5" (127mm) long wire

 



ProdutosRelacionados